咨询热线
当前位置: 首页 > 新闻媒体 > 公司动态 >

1、复核洞口与产品尺寸是否相符,防火卷帘门的洞口尺寸,可根据3M。

1, check whether the hole is in conformity with the product size, and the size of the opening of the fire shutter door can be calculated according to 3M.

2、确定安装水平线及垂直线,按设定尺寸依次安装.槽口尺寸应准确,上下保持一致,对应槽口应在同一平面内,然后用连接件与洞口内的预埋件焊牢。

2. Determine the installation horizontal and vertical lines, and install them in turn according to the set dimensions. The groove size should be accurate and consistent, and the corresponding groove should be in the same plane, and then welded firmly with the embedded parts in the hole.

3、卷门机必须按说明书要求安装。

3, rolling door machine must be installed according to the instructions.

4、卷轴、文架板必须牢固地装在混凝土结构上或预埋件上。

4, reel and rack plate must be firmly installed on concrete structure or embedded parts.

20161214578645.gif

5、宽大门体需在中间位置加装中柱,两边有滑道.中柱安装必须与地面垂直,安装牢固,但要拆装方便。

5. Wide gate body should be installed in the middle of the column, both sides of the slide. The installation of the column must be vertical to the ground, installation firm, but to disassemble and install conveniently.

6、门体叶片插入滑道不得少于30mm,门体宽度偏差为土3mm。

6, door body blade insert slideway must be less than 30mm, door width deviation is soil 3mm.

7、防火卷帘门水幕系统装在防护理下面,喷嘴倾斜15°角。

7, fire shutter door water curtain system installed under the prevention of care, nozzle tilt 15 degrees angle.

8、安装完略,先手动调'自试运行,观察门体上下运行情况,正常后通电调试。

8. Installation is short, first manually adjust the'self-test operation, observe the operation of the door body up and down, after normal power-on debugging.

9、观察卷帘机、传动系统、门体运行情况应启闭正常、顺畅,速度为3-7米/分钟。

9. Observing the operation of rolling shutter, transmission system and door body should be opened and closed normally and smoothly with a speed of 3-7 m/min.

10、调整制动器外壳方向,使环形链朝下;调整链条张紧度,链条6-10mm;调整单向调节器及限位器。

10. Adjust the direction of the brake housing to make the ring chain face down; adjust the chain tension, chain 6-10mm; adjust the unidirectional regulator and limiter.

11、卷筒安装应先找好尺寸,并使卷简轴保持水平位置。注意与导轨之间的距离应两端保将一致,临时固定后进行检查,并进行必要的调篷、校正,无误后再与支架预埋件用电焊焊接。

11, reel installation should first find a good size and keep the reel shaft horizontal. Attention should be paid to the distance between the guide rail and the two ends of the same, temporarily fixed after inspection, and necessary adjustments, corrections, no error and bracket embedded parts after welding.

本文的精彩内容来自:济南遥控车库门更多的详细内容请点击我们的官方网站:http://www.kdjlm.com谢谢您的到来

The highlight of this article comes from: Jinan remote control garage door more details please click our official website: http://www.kdjlm.com Thank you for coming


上一篇:遥控车库门在建设的时候尺寸标准
下一篇:电动车库门的电源的安装方式
产品中心
联系我们