咨询热线
当前位置: 首页 > 新闻中心 > 公司动态 >

卷帘门电机的运用方法

发布人:http://www.kdjlm.com    发布时间:2017-02-20 11:49:28

卷帘门电机如何正确的运用,下面由济南卷帘门厂家的小编为您介绍一下:
How to use the rolling door motor, the following by the Ji'nan rolling shutter door manufacturers to introduce you:
1、电机工作环境应保持干燥,电动机外表应保持清洁,进风口不应受尘土、纤维等阻止。
1, the motor working environment should be kept dry, motor appearance should be kept clean, air inlet should not be dust, fiber, etc..

20161214750871.jpg2、当电动机的热保护接连发作动作时,应查明问题来自电动机的超负荷运行或热保护设备设定值太低,消除故障后,方可投入运转。
2, when the motor thermal protection after a series of attacks, the problem should be identified from the overload operation of the motor or thermal protection equipment set value is too low, to eliminate the fault before they can be put into operation.
3、应保证电动机在运转的润滑,即应弥补或替换 光滑脂运转中发现轴承过热或光滑蜕变时,液压 及时换光滑脂。替换光滑脂时,应铲除旧的光滑油,并有汽油洗净轴承及轴承盖的油槽,然后将 ZL-3锂基脂 填充轴承内外圈之间的空腔的 1/2 对 2 极(及 2/3 对4 6 8 极)。
3, should ensure that the motor in the operation of lubrication, that should be made up or replace the smooth operation of the grease found bearing overheating or smooth disintegration, hydraulic timely for smooth grease. Replace the grease, oil should be the eradication of the old, and the oil tank of gasoline to clean the bearing and bearing cover, and then the ZL-3 lithium grease filled cavity between the inner and outer rings of the bearing of the 1/2 on the 2 (and 2/3 468 pole).
4、当轴承的寿命终了时,电动机运转的振荡及噪声将显着增大,查看轴承的径向游隙抵达下列值时,即应替换轴承。
4, when the end of the life of the bearing, the vibration and noise of motor will be significantly increased, the radial clearance of the bearing in view the following values, which should replace the bearings.
5、设备电动机时,从轴伸端或非伸端取出转子都能够。若是没有必要卸下电扇,仍是从非轴伸端取出转子较为便当,从定子中抽出转子时,应防止损坏定子绕组或绝缘。
5, when the motor equipment, from the shaft extension or non end rotor can be removed. If it is not necessary to remove the fan, or from the non shaft extending end out rotor is more convenient, from out of the rotor stator, stator winding insulation should prevent damage or.
6、替换绕组时有必要记下原绕组的办法,尺度及匝数,线规等,当丢失了这些数据时,应向制作厂讨取,随意更改原描绘绕组,常常使电动机某项或几项功用恶化,乃至于无法运用。
6, it is necessary to replace the winding down of the primary winding way, scale and number of turns of wire, etc., when the loss of the data, to get production plant, change the original picture often make the motor winding, one or several function deterioration, and cannot be used.

上一篇:防盗门选购需注意的要点
下一篇:谈谈大家对济南车库门的认识
产品中心
联系我们