咨询热线
当前位置: 首页 > 新闻媒体 > 公司动态 >

卷帘门的芯和棍是怎么衔接的?

发布人:http://www.kdjlm.com    发布时间:2019-05-28 13:27:08

  卷帘门实心腹板钢窗核心与上杠之间的连接,窗为直窗,窗框为t形。窗芯与梅花头的连接有多种标准:如2507窗芯材料与3201窗芯材料连接良好时,应选用17.5mm梅花头;又如2507窗心料和3202、3203窗扇料、3204窗扇料依次选用9.5mm梅花头。图4-19为窗芯梅花头形状示意图。

  The connection between the solid web steel window core and the upper bar of the rolling shutter door is straight window and the window frame is t-shaped. There are many standards for the connection between window core and plum blossom head: if the connection between 2507 window core material and 3201 window core material is good, 17.5mm plum blossom head should be selected; for example, 2507 window core material and 3202, 3203 window fan material, 3204 window fan material should be selected 9.5mm plum blossom head in turn. Figure 4-19 is a sketch of the shape of the plum blossom head with window core.

  青岛芯卷帘门门窗,美观大方,可与窗框连接的加工工艺是2至瑞德、窗杆、旋片和窗框芯均匀按下。冲好美工拿着冲模冲进了印刷机。核心栏的两端又有窗口。在冲床上用模切成要求标准的压头。然后相应的美孔美把头伸进窗户。与电加热“美机唱'强。

  Qingdao core rolling curtain doors and windows, beautiful and generous, can be connected with the window frame processing technology is 2 to Rhett, window pole, screw and window frame core press uniformly. The puncher took the die and rushed into the press. There are windows at both ends of the core bar. Cut the die into the required standard press head on the punch. Then the corresponding Mekongmei put her head into the window. With electric heating, "beautiful machine singing" strong.

20161214578645.gif

  卷帘门双平开式实心腹板钢门和无直开式实心腹板钢窗,合在一起构成一个封闭的配合面,其中必须采用3203和3202两种风机材料相互连接。有两种衔接方法:

  Double flat open solid web steel doors and non-open solid web steel windows of rolling shutter doors are combined to form a closed mating surface, in which 3203 and 3202 fan materials must be used to connect each other. There are two ways of cohesion:

  (1)焊接连接方式:选择焊接连接风机材料,如图所示。其加工过程如下:首先,用立式符号片3203和卧式种子片3202的相邻端两种风机材料压机45?角冲裁后,再根据冲压模具的尺寸要求将大翼板切成平头。

  (1) Welding connection mode: Select welding connection fan material, as shown in the figure. The processing process is as follows: Firstly, after 45? Angle blanking with vertical symbolic sheet 3203 and horizontal seed sheet 3202, the large wing plate is cut into flat head according to the size requirement of the punching die.

  (2) meitou衔接方法:选用meitou sing’fan material。橡胶接头的加工工艺是什么?按所要求的形状在镇里冲加工成扁型和梅花孔,再将横杆3202材料,用模具装进展台。

  (2) Meitou connection method: Meitou sing'fan material is selected. What is the processing technology of rubber joint? Punch flat and plum blossom holes in Zhenli according to the required shape, then use 3202 material of cross bar to install progressive stage with die.


上一篇:卷帘门的弹簧如何更换?
下一篇:最后一页
产品中心
联系我们

【本站图片均由网站所有方提供,部分图 片来源于网络,如有任何疑问请第一时间与我们联系,未经沟通本站不承担相关法律责任!】