咨询热线
-->
当前位置: 首页 > 新闻中心 > 公司动态 >

抗风卷帘门应用及安装流程

发布人:http://www.kdjlm.com    发布时间:2020-08-12 15:23:17

抗风卷帘门常用于一些高层建筑,或是其他的一些场合作为防火设施,安装抗风卷帘门的时候要按照顺序操作,先安装铁板,然后安装圆管和电机,接着安装门,而后按照尺寸将轨道安装好,施工完成后需要做调试,下面是详细介绍。  
The wind resistant rolling shutter door is often used in some high-rise buildings or other occasions as fire-proof facilities. When installing the wind resistant rolling shutter door, it should be operated in accordance with the sequence. First install the iron plate, then install the round pipe and motor, then install the door, and then install the track according to the size. After the construction is completed, it needs to be debugged. The following is a detailed introduction.
一、抗风卷帘门应用范围
1、 Application scope of wind resistant rolling shutter door
1、抗风卷帘门是现代高层建筑当地非常不可缺少的卷帘设施之一,抗风卷帘门除了具有欧式卷帘门以外功能之外,还具有非常好的防火、隔烟、抑制火灾蔓延、保护人员疏散的特殊功能,广泛应用于高层建筑、大型商场等人员密集的场合。
1. Wind resistant rolling shutter door is one of the most indispensable rolling shutter facilities in modern high-rise buildings. In addition to the functions of European style rolling shutter door, it also has very good fire prevention, smoke isolation, fire spread suppression and personnel evacuation protection. It is widely used in high-rise buildings, large shopping malls and other crowded places.
2、划分防火分区,控制分区建筑面积所设防火墙和防火隔墙上的门。当建筑物设置防火墙或防火门有困难时,要用防火卷帘门代替,同时须用水幕保护。
2. Divide the fire compartment, control the building area of the partition, set up the firewall and the door on the fire partition wall. When it is difficult to install fire wall or fire door in the building, fire shutter door should be used instead and water curtain should be used for protection.
3、在某些场合,建筑内不配备消防中央控制系统,抗风卷帘门仅借助于防火卷帘门的消防控制电器箱实现防火卷帘门的防火规定运行程序。在这种情况下,当火警发生时,烟雾传感器接收的火警信号直接传至抗风卷帘门的消防控制电器箱。
3. In some cases, the building is not equipped with a central fire control system, and the wind resistant rolling shutter door only relies on the fire control electrical box of the fire shutter door to realize the fire prevention operation procedure of the fire shutter door. In this case, when a fire occurs, the fire signal received by the smoke sensor is directly transmitted to the fire control electrical box of the wind resistant rolling shutter door.
二、抗风卷帘门安装流程
2、 Installation process of wind resistant rolling shutter door
1、安装大小铁板:抗风卷帘门大小铁板的安装又分为垂直安装和水平安装两种,其中垂直安装主要用于大铁板的下口,门洞口向上5cm来确定安装位置。水平安装则是以圆管长度减去门洞长度加2cm除以2,两边平分来确定大小铁板之间位置安装。小铁板以大铁板的中心点水平来确认小铁板的水平点安装位置。
1. Installation of large and small iron plates: the installation of large and small iron plates of wind resistant rolling shutter door can be divided into vertical installation and horizontal installation. The vertical installation is mainly used for the lower opening of large iron plate, and the installation position is determined by 5cm upward of the door opening. For horizontal installation, the length of the round pipe minus the length of the door opening plus 2cm divided by 2, and the two sides are equally divided to determine the position between the large and small iron plates. The installation position of the small iron plate is confirmed by the level of the center point of the large iron plate.
2、安装圆管:将圆管有缺口一侧套在大铁板的链盘上,再将轴承座套在圆管轴头上,用螺丝将轴承座紧固在小铁板上。
2. Install the round pipe: put the notched side of the round pipe on the chain plate of the large iron plate, then put the bearing seat on the shaft head of the round pipe, and fasten the bearing seat on the small iron plate with screws.
3、安装电机: 抗风卷帘门的电机在安装一定要牢固,链条松紧应适当。电机上的所有接线头需用电工胶带缠紧,禁止将多余电源线缠绕在电机上,以防止电机发热造成的电源线漏电、短路等安全隐患。
3. Installation of motor: the motor of anti wind rolling shutter door must be firmly installed and the chain should be appropriate. All terminals on the motor shall be wrapped tightly with electrical tape. It is forbidden to wind the redundant power line on the motor to prevent the power line leakage, short circuit and other potential safety hazards caused by motor heating.
4、安装门体:将电动抗风卷帘门的吊沿片、底梁串到门片上,门片通过电机上升至适当位置,再将吊沿片紧固在圆管上,进行上下调整,保持上下对齐,加紧门片,防止窜体卡口。
4. Installation of door body: string the hanging edge piece and bottom beam of the electric wind resistant rolling shutter door onto the door piece, and the door piece is lifted to the appropriate position through the motor, and then the hanging edge plate is fastened on the round pipe for up and down adjustment, keeping the upper and lower alignment, tightening the door piece, and preventing the channeling bayonet.
5、安装导轨:将事先依照尺寸、要求制作好的抗风门导轨立于门洞两侧,注意上下两头需保持在一条水平线上。再用膨胀螺栓固定轨道,结束后盖好导轨封盖。
5. Installation guide rail: set the anti wind door guide rail made according to the size and requirements in advance on both sides of the door opening, and pay attention to keep the upper and lower ends in a horizontal line. Then fix the track with expansion bolt and finish the cover of guide rail.
6、调试限位:抗风卷帘门的限位在电机里,打开电机外壳,调整门体的上、下限位,要求上限位最少离门洞有一个底梁位置,下限位要求与地面密封。多次反复试验几次,直到上下开门达到理想位置即可停止。
6. Debugging limit: the limit of the wind resistant rolling shutter door is in the motor. Open the motor shell, adjust the upper and lower limits of the door body. It is required that the upper limit is at least one bottom beam position from the door opening, and the lower limit is required to be sealed with the ground. Repeat the test several times until the upper and lower doors reach the ideal position.
上一篇:济南卷帘门的外观验收要求有哪些?
下一篇:门板对于车库门的起到的什么作用?
产品中心
联系我们