咨询热线
-->
当前位置: 首页 > 新闻中心 > 公司动态 >

快速卷帘门的电机的日常维护要点!

发布人:http://www.kdjlm.com    发布时间:2020-11-06 16:14:20

快速卷帘门是快速升降的无障碍隔离门,主要功能是保温、保湿、防尘、防虫、隔音等,使车间保持恒温、恒湿、洁净的工作环境。适用于食品、医药、电子、橡胶、化工、汽车、纺织、物流等领域。
The fast rolling shutter door is a barrier free isolation door with rapid lifting. Its main functions are heat preservation, moisture preservation, dust prevention, insect prevention and sound insulation, so as to maintain a constant temperature, constant humidity and clean working environment in the workshop. It is suitable for food, medicine, electronics, rubber, chemical industry, automobile, textile, logistics and other fields.
快速卷帘门的运作主要就是靠电机,所以日常维护对电机的使用很重要!下面就来为您简述一下快速卷帘门电机的几个维护要点:
The operation of the fast rolling shutter door mainly depends on the motor, so the daily maintenance of the motor is very important! The following will briefly describe the maintenance points of the motor of fast rolling shutter door:
1、快速卷帘门的电机运用时应在干燥环境中进行,电机表面应保持洁净,进风口不能有灰尘、纤维等。
1. The motor of the fast rolling shutter door should be used in a dry environment. The surface of the motor should be kept clean and there should be no dust and fiber in the air inlet.
2、当电念头的热维护延续发作举措时,应查明毛病来自电念头照样超负荷或维护安装整定值太低,消弭毛病后,方可投入运转。
2. When the thermal maintenance of the electric motor continues to take action, it should be found out that the problem comes from the overload of the electric motor or the setting value of the maintenance and installation is too low. After the problem is eliminated, it can be put into operation.
3、应该保证电念头在运转进程中的光滑无障碍。普通的电念头运转5000小时左右,即应增补或改换光滑脂,运转中发现轴承过热或光滑蜕变时,液压实时换光滑脂。
3. The smooth and unobstructed operation of the motor should be ensured. When the ordinary electric motor runs for about 5000 hours, the grease should be added or replaced. When the bearing is overheated or smooth degeneration is found in operation, the grease is changed by hydraulic pressure in real time.
4、当轴承的寿命终了时,电念头运转的噪声将明显增大,反省轴承的径向游隙到达下列值时,即应改换轴承。
4. When the service life of the bearing is over, the noise of the motor will increase obviously. When the radial clearance of the bearing reaches the following value, the bearing should be replaced.
5、拆开电念头时,从轴伸端或非伸端掏出转子都可以。假如没有需要卸下电扇,照样从非轴伸端掏出转子较为便当,从定子中抽出转子时,应避免损坏定子绕组或绝缘。
5. When the motor is disassembled, the rotor can be pulled out from the extended or non extended end of the shaft. If there is no need to remove the fan, it is more convenient to take out the rotor from the non shaft extension end. When pulling out the rotor from the stator, the stator winding or insulation should be avoided.
6、改换绕组时必需记下原绕组的方式,尺寸及匝数,线规等,当丢失了这些数据时,应向制造厂讨取,随意更改原设计绕组,经常使电念头某项或几项功能恶化,甚至于无法运用。
6. When changing the winding, it is necessary to record the mode, size, turns, wire gauge, etc. of the original winding. When these data are lost, they should be obtained from the manufacturer, and the original designed winding can be changed at will. As a result, some or several functions of the electric motor will be deteriorated or even can not be used.
上一篇:别墅车库门中的平轮有什么作用?
下一篇:哪种材质的车库门更具防盗性能
产品中心
联系我们