咨询热线
-->
当前位置: 首页 > 新闻中心 > 公司动态 >

卷帘门钥匙转不动、拔不出来怎么办?

发布人:http://www.kdjlm.com    发布时间:2021-03-02 13:48:35

卷帘门的机械锁是目前门类产品中使用频率最低的产品,没有之一,由于长时间不使用会导致锁具生锈、卡顿等现象的出现,导致卷帘门的钥匙插不进去、转不动、拔不出来等种种问题,那么,一旦遇到这种现象如何解决呢?
At present, the mechanical lock of rolling shutter door is the product with the lowest frequency of use in the door products, and it is not one of the products. Because it is not used for a long time, it will lead to the appearance of the lock rust, stuck and other phenomena, resulting in the rolling shutter door key can not be inserted, turned, pulled out and other problems. Then, once this phenomenon is encountered, how to solve it?
首先要分析卷帘门机械锁故障的原因,仔细观察,才能找到有效的解决方案。我们可以逐一分析。
First of all, it is necessary to analyze the causes of the failure of the mechanical lock of the rolling shutter door, and carefully observe it, in order to find an effective solution. We can analyze them one by one.
1·锁芯内有泥土等故障:由于卷帘门的锁芯在底部,距离地面很近,平时的走路、风吹、雨淋等都有可能导致灰尘泥土进入锁芯,此时如果发现锁芯内有泥土,先不要着急插钥匙,用别针、牙签等工具清理锁芯内的泥土,然后用易挥发的润滑油润滑,干燥后用固体润滑剂石墨进行润滑,一定要定期检查清理杂物。
1. There are soil and other faults in the lock cylinder: because the lock cylinder of the rolling shutter door is at the bottom and very close to the ground, usually walking, wind blowing, rain and so on may cause dust and soil to enter the lock cylinder. At this time, if there is soil in the lock cylinder, do not rush to insert the key, use pins, toothpicks and other tools to clean the soil in the lock cylinder, and then use volatile lubricating oil to lubricate, and use solid lubricant after drying Lubricant graphite lubrication, be sure to regularly check and clean up debris.
济南卷帘门
济南卷帘门
Jinan rolling shutter door
2·锁芯内有异物:锁芯内有异物80%以上都是恶作剧或者故意报复,人为的将竹签、胶水等灌注到锁芯内,这种情况钥匙一般插不进去,如果是牙签、竹签等异物,可以尝试用别针抠出来,如果扣不出来就只能暴力换锁了,如果是胶水灌注,则必须换锁了。
2. There are foreign matters in the lock cylinder: more than 80% of the foreign matters in the lock cylinder are pranks or deliberate retaliation, and the bamboo stick and glue are artificially poured into the lock cylinder. In this case, the key can not be inserted. If it is toothpick, bamboo stick and other foreign matters, you can try to pick them out with a pin. If you can't buckle them out, you can only change the lock violently. If it is glue pouring, you must change the lock.
3·长时间不使用导致锁具生锈:这种是最常见的一种现象,首先润滑是必须的,而且使用固体润滑剂,用小孩的铅笔笔芯粉末,撒到钥匙上,插入锁芯后反复旋转,让石墨粉均匀分布就可以了,此时就会感觉到钥匙进出都非常顺畅。
3. Long time disuse leads to lock rusting: This is the most common phenomenon. First of all, lubrication is necessary, and solid lubricant is used. Use children's pencil lead powder, sprinkle it on the key, insert it into the lock core and rotate it repeatedly, so that the graphite powder is evenly distributed. At this time, you will feel that the key is very smooth in and out.
如果是钥匙已经插进去了,转不动,拔不出来,此时就要详细回忆插入钥匙都做了哪些动作,一般这种现象都是钥匙插反、查的不到位等原因,在轻度旋钮钥匙后,钥匙孔抱死,钥匙动不了了,此时只要按照原来动作的相反动作操作,也就是让钥匙复位到刚插入的状态,调整钥匙深浅或者加入润滑剂。
If the key has been inserted, can't turn, can't pull out, at this time we have to recall in detail what actions have been done to insert the key. Generally, this phenomenon is caused by the key inserted reversely, the check is not in place and so on. After slightly turning the key, the key hole is locked, and the key can't move. At this time, we just need to operate according to the opposite action of the original action, that is, to reset the key to the just inserted position Adjust the key depth or add lubricant.
此时,钥匙就可以正常使用了。但是,这仅仅是低级错误;很多时候往往都是这样的动作,钥匙没有完全插入,拧半圈拧不动,发现钥匙没有插入到位,直接继续插入,继续拧钥匙就卡死了;又或者插入钥匙拧了半圈拧不动,准备拔出来,拔了一点点拔不动,继续拧,钥匙卡死了。
At this time, the key can be used normally. However, this is only a low-level error; most of the time, it's like this: if the key is not fully inserted and can't be turned by half a turn, if you find that the key is not inserted in place, you can continue to insert it and continue to turn the key, and then it's stuck; or if you insert the key and can't turn it by half a turn, you're ready to pull it out.
上一篇:卷帘门开门时怎么发生感应的你知道吗?
下一篇:看完这些你还敢说你了解济南卷帘门吗?
产品中心
联系我们