咨询热线
当前位置: 首页 > 新闻中心 > 公司动态 >

车库门厂家教您如何自行调整行程距离

发布人:http://www.kdjlm.com    发布时间:2021-09-27 10:26:27

自动车库门行程的设置可以完成车库门开关门行程限位的确定,并自动实现开关门过程中力量的检测和力量的默认选定。行程距离不准确会影响到电动车库门正常使用,为了节省人力、财力,不少人会通过自己动手来进行调整,下边车库门厂家教您如何自行调整行程距离的方法。
The setting of automatic garage door stroke can determine the limit of garage door opening and closing stroke, and automatically realize the detection and default selection of force in the process of opening and closing. The inaccurate travel distance will affect the normal use of the electric garage door. In order to save manpower and financial resources, many people will adjust it by themselves. The garage door factory below teaches you how to adjust the travel distance by yourself.
按下控制板上的Func键,此时运行灯开始闪烁,按住该键超过8秒,运行灯正常亮,此时程序进入开合行程和过载学习过程;
Press the func key on the control board, and the operation light starts to flash. Press and hold the key for more than 8 seconds, and the operation light is normally on. At this time, the program enters the opening and closing stroke and overload learning process;
济南车库门
按Inc键。这时,马达开始朝着开门的方向运转。按住键。马达从低速运转到高速。同时,运行指示灯闪烁,表示电机向上运行。当您到达理想位置时,松开按钮,电机停止运行;如果按DEC键,电机从缓慢至快速运行,以关闭车门,且STA灯闪烁。用这两个按钮来调整上面的位置。
Press the Inc key. At this time, the motor starts to run in the direction of opening the door. Press and hold the key. The motor runs from low speed to high speed. At the same time, the operation indicator flashes, indicating that the motor runs upward. When you reach the ideal position, release the button and the motor stops running; If the DEC key is pressed, the motor runs from slow to fast to close the door, and the sta light flashes. Use these two buttons to adjust the position above.
如果位置调整适当,按func键一次,则运行指示符将闪烁并关闭,指示上面的学习完成;同时,STA指示灯亮,节目进入下一步学习过程;
If the position is adjusted properly, press func once, the operation indicator will flash and close, indicating that the above learning is completed; At the same time, the sta indicator light is on, and the program enters the next learning process;
用Inc和Dec两个键调整下位置。到达预定位置后,按一次func键,此时sta灯闪烁,表示下位学习完成;
Use the Inc and dec keys to adjust the lower position. After reaching the predetermined position, press the func key once. At this time, the sta light flashes, indicating that the lower learning is completed;
在门体的运行过程中,该程序在门体的运行过程中自动测量门体的阻力。在到达适当位置后,程序自动停止,在一段时间的延迟之后,程序自动关闭门,此时,STA灯点亮,程序测量关门时的强度,到达适当位置后,程序自动停止;
During the operation of the door body, the program automatically measures the resistance of the door body during the operation of the door body. After reaching the appropriate position, the program will automatically stop. After a period of delay, the program will automatically close the door. At this time, sta light will be on, and the program will measure the strength when closing the door. After reaching the appropriate position, the program will automatically stop;
力量学习完成后,保存所有学习值,run和sta灯多次闪烁,表示程序学习完成;
After the strength learning is completed, save all learning values, and the run and sta lights flash for many times, indicating that the program learning is completed;
此时按遥控上的按钮或墙上开关上的按钮,电机就会按要求运行。
At this time, press the button on the remote control or the button on the wall switch, and the motor will run as required.
上一篇:车库门卷帘、翻板两种类型介绍
下一篇:茗鑫门业介绍卷帘门的设置要求
产品中心
联系我们