咨询热线
当前位置: 首页 > 新闻中心 > 行业新闻 >

电动卷帘门给你不一样的体验

发布人:http://www.kdjlm.com    发布时间:2017-03-28 16:57:04

  我们都清楚电动卷帘门应用极为广泛,不仅操作方便,而且造型越来越美观,这是消费者选择的主要原因。不过,在使用过程中会遇到一些故障,济南卷帘门给大家讲述下怎样解决电动卷帘门故障。
We all know that electric shutter application is very wide, not only easy to operate, and more and more beautiful modelling, this is the main reason for consumers to choose. In use process, however, will have some trouble, under the jinan electric rolling door to talk about how to solve electric shutter fault.
  一、电动机不动或转速慢此故障原因一般是线路断路、电机烧损、停止按钮没复位、限位开关动作、负载较大等引起。
Fixed or an, motor speed slow this is the cause of the problem in the general line open circuit, motor loss, stop button didn't reset, limit switch action, larger load, etc.
  处理方法:检查线路、并接通;更换烧损电机;更换按钮或重复按动几次; 拨动限位开关滑块使它脱离微动开关触点, 并调整微动开关位置;检查机械部分 有无卡阻,若有则消除卡阻清理障碍物。
Processing method: check the line, and connected; Replace the burning motor; Replace the repeat push button or several times; Limit switches slider to make it out of the micro switch contact, and adjust the micro switch position; Check whether there is any jam on mechanical parts, if there is eliminate jam clear obstacles.
  二、控制失效故障发生的部位及原因:继电器触点粘死、行程微动开关失效 或触片变形、滑块紧定螺钉松、靠板螺丝松使靠板移位,使滑块或螺母不能随丝 杆转动而移动、限位器传动齿轮破损、按钮上、下键卡死。
Second, the control part and the reasons of the failure happened: relay contact stick to death, micro switch failure Or contact deformation, the slider tight set screw loose, by plate screws that by displacement of plate, the slider or nut can't move with screw rotation, stop driving gear damage, button, the key card to death.
  处理方法:更换继电器;更换微动开关或触片;紧定滑块螺钉并 使靠板复位;更换限位器传动齿轮;更换按钮。

济南卷帘门Processing method: change the relay; Change the micro switch or touch; Set the slider screw and to reset the on board; Replace the stop transmission gear; Change the button.
  三、手拉链不动,故障原因:环形链条堵住十字槽;棘爪无脱离棘轮;压链架卡死。
Three, hand zipper, the cause of the problem: circular chain block cross slot; Ratchet without out of ratchet; Chain frame jammed.
  处理方法:理顺环形链条;调整棘爪与压链架相对位置;更换或润滑销轴。
Processing method: smooth circular chain; Adjust the pawl and chain frame position; Replace or lubrication pin.
  四、电机振动或噪声较大,故障原因:刹车盘不平衡或断裂;刹车盘无紧固;轴承失油或失效;齿轮啮合不顺、失油或磨损严重;电机电流声或振动。
Four, motor vibration or noise is bigger, the cause of the problem: the brake disc imbalance or fracture; Brake disc without fastening; Bearing oil loss or failure; Gear mesh, serious loss of oil or wear; Electrical mechanical and electrical LiuSheng or vibration.
  处理方法:更换刹车盘或重新调整平衡;紧固刹车盘螺母;更换轴承;修配电机轴输出端齿轮、润滑或更换;检查电机,如电机坏损则更换。
Methods: replace the brake disc or readjust the balance; Tighten the brake disc nut; Replace the bearing; And replacement motor shaft output gear, lubrication or replacement; Check the motor, such as motor bad loss is replaced.
  我们以优良的产品,完美的服务,可靠的信誉,为您的事业成功助一臂之力,竭诚欢迎各界同仁惠顾洽谈业务!
With our excellent products, perfect service, reliable credit, for your career success help, sincerely welcome all circles to patronize negotiate business!

上一篇:遥控车库门的故障和处理方法
下一篇:电动卷帘门的优势
产品中心
联系我们