咨询热线
当前位置: 首页 > 新闻媒体 > 行业新闻 >

卷帘门的限位怎么调整?

发布人:http://www.kdjlm.com    发布时间:2019-05-30 11:30:11

  很多卷帘门的客户反映,门落不到底,门抬不到顶,诸如此类。这种情况首先要排除门体导轨和电机传动机构是否卡死,但经常发生门体不落到底,升不上顶,一般是限位开关位置误差造成的。

  Many customers of rolling curtain doors reflect that doors can not fall to the bottom, doors can not lift to the top, and so on. In this case, we should first rule out whether the door guide rail and the motor drive mechanism are jammed, but it often happens that the door body does not fall to the bottom and does not rise to the top, which is generally caused by the position error of the limit switch.

  所以对于卷帘门的限位开关究竟如何调整,我们首先要介绍一下限位开关的原理。

  So for how to adjust the limit switch of the curtain door, we should first introduce the principle of the limit switch.

  限位开关是一种简单的开关式传感器,它是一种开关,用来检测物体是否已经到达位置。它属于机械触发器类。当物体接近限位开关时,它就会触发。

  Limit switch is a simple switching sensor. It is a switch used to detect whether the object has reached its position. It belongs to the category of mechanical triggers. When an object approaches the limit switch, it triggers.

  那么卷帘门的限位开关起什么作用呢?

  So what role does the limit switch of the curtain door play?

  上升或下降的快门由电动机控制,当你按下向上或向下按钮,电动机根据相应的方向,使它停止的高位和低位限位开关控制,当门运行高限位开关,限位开关触发电动机停止信号,因此本门停止,或增加快门会使整个快门电动机传动部件受损,或者销毁。滚动门运行到最低点也是如此。

20161219618477.jpg

  The up or down shutter is controlled by the motor. When you press the up or down button, the motor will stop the high and low limit switch according to the corresponding direction. When the door runs the high limit switch, the limit switch triggers the motor stop signal. Therefore, the stop of the gate or the increase of the shutter will damage or destroy the whole shutter motor drive component. This is also true of rolling doors running to the bottom.

  因此,限位开关在对卷帘门起电路控制的同时也起着至关重要的保护作用。

  Therefore, the limit switch plays an important role in protecting the curtain door circuit.

  调整限位开关的位置更细腻,如果最低限制过高,它会显示,百叶窗不跌至底部的现象,如果最高限额太低了,它就会出现,使用百叶窗不达到顶峰的现象。

  Adjusting the position of limit switch is more delicate, if the minimum limit is too high, it will show that the louver does not fall to the bottom of the phenomenon, if the maximum limit is too low, it will appear, the use of louvers does not reach the peak.

  在调节时,先松开两个限位开关的螺丝,然后手动将卷帘门调到最低点,当卷帘门刚达到最低点时,此时在电机上,将最低限位开关调整到刚刚触发状态,然后拧紧螺丝。同样,手动将卷帘门调到最高点,当卷帘门刚达到最高点时,再在电机上,将最高限位开关调整到刚刚触发状态,然后拧紧螺丝。

  When adjusting, first loosen the screw of two limit switches, then manually set the shutter door to the lowest point. When the shutter door just reaches the lowest point, at this time, on the motor, adjust the minimum switch to the just triggered state, and then tighten the screw. Similarly, manually adjust the curtain door to the highest point. When the curtain door has just reached the highest point, then on the motor, adjust the maximum limit switch to the just triggered state, and then tighten the screw.

  完成以上步骤后,用按钮控制、打开、关闭几次,观察卷帘门是否达到该位置,重复三次是否正常,宣布调整完毕。

  After completing the above steps, use buttons to control, open and close several times, observe whether the rolling shutter door reaches the position, repeat three times normally, announce that the adjustment is completed.


上一篇:车库门工业门是怎么增加门板强度的?
下一篇:最后一页
产品中心
联系我们

【本站图片均由网站所有方提供,部分图 片来源于网络,如有任何疑问请第一时间与我们联系,未经沟通本站不承担相关法律责任!】