咨询热线
当前位置: 首页 > 新闻媒体 > 行业新闻 >

车库门固定式扭簧接头工艺流程!

发布人:http://www.kdjlm.com    发布时间:2020-03-26 14:44:03

  手动车库门和自动车库门的主要区别是没有马达。自动库门主要分为:转动盘车库门和卷帘车库门,当门较大时,不方便安装在地面门体处,车库门起着方便、快捷的开启作用。在现有的自动切库门,是一种常见的转板切库门,切库门配有减震弹簧平衡系统,其原则是扭转弹簧平衡系统产生的扭矩和门的质量,扭转弹簧平衡系统的帮助下实现上下运动。由于使门体处于“零重量”状态,靠滑轮在轨道内运行,因此阻力小,能耗小,而且维修率低,耐磨性好。扭转管通常安装有两个相互连接的扭转弹簧,扭转弹簧两端分别安装有固定弹簧接头和旋转弹簧接头。

  The main difference between a manual garage door and an automatic garage door is that there is no motor. The automatic garage door is mainly divided into: rotary disc garage door and rolling shutter garage door. When the door is large, it is inconvenient to install on the ground door body, and the garage door plays a convenient and quick role in opening. In the existing automatic cutting door, it is a common rotating plate cutting door. The cutting door is equipped with a damping spring balance system. Its principle is the torque generated by the torsion spring balance system and the quality of the door. With the help of the torsion spring balance system, the up and down movement is realized. Because the door body is in the "zero weight" state and runs in the track by the pulley, the resistance is small, the energy consumption is small, and the maintenance rate is low, and the wear resistance is good. The torsion tube is usually equipped with two mutually connected torsion springs, both ends of which are respectively equipped with fixed spring joints and rotary spring joints.

  目前,车门的固定扭转弹簧接头采用铁制件,重量大,使用寿命短,成本高,环境污染严重。车库门常用的固定扭转弹簧接头是由一个整体构成的。在接头体下方的安装体上嵌有扭力弹簧,然后将扭力弹簧接头固定在扭力管上。虽然扭力弹簧联合是重量轻和低成本,发现扭力弹簧的同心度关节扭力弹簧的两端是可怜的安装后,在长期使用和磨损程度高,导致使用寿命短。

20161214103489.jpg

  At present, the fixed torsion spring joint of the door is made of iron, which has the advantages of large weight, short service life, high cost and serious environmental pollution. The fixed torsion spring joint commonly used in garage door is composed of a whole. A torsion spring is embedded in the mounting body under the joint body, and then the torsion spring joint is fixed on the torsion pipe. Although the combination of torsion spring is light in weight and low in cost, it is found that the two ends of the concentricity joint torsion spring of torsion spring are pitifully installed after long-term use and high wear, resulting in short service life.

  车库门开关固定扭力弹簧接头,包括关节本体和本体位于关节底部的安装,安装后体位扭力弹簧,在连接器的身体的中心配备安装槽,关节沿径向的本体固定身体和第二固定身体,和固定的身体和第二固定体位于同一行的中心,第一固定身体的配备第一安装孔,第二固定在身体配备第二安装孔,安装在身体上配备了第一个线程描述的第一线槽和槽相对于第二线槽,第一个线程之间的缺口槽和第二个槽。避免了扭转管的抖动,有利于改善车库门安装后带有固定扭转弹簧接头的同轴性,有效减少了磨损,提高了门的使用寿命。

  The fixed torsion spring joint of garage door switch includes the installation of joint body and body at the bottom of joint. After installation, the body position torsion spring is installed. The center of the body of the connector is equipped with an installation groove. The joint is fixed with the body along the radial direction and the second fixed body, and the fixed body and the second fixed body are located in the center of the same line. The first fixed body is equipped with a first installation hole, The second fixing is provided with a second mounting hole on the body which is provided with a first slot and a slot described by the first thread relative to the second slot, a notch slot and a second slot between the first thread. The utility model can avoid the shaking of the torsion tube, improve the coaxiality of the fixed torsion spring joint after the garage door is installed, effectively reduce the abrasion and improve the service life of the door.


上一篇:车库门来回开关不严怎么办?
下一篇:如何安装高效的快速卷帘门?
产品中心
联系我们