咨询热线
当前位置: 首页 > 新闻中心 > 行业新闻 >

电动卷帘门的限位器该如何调节?

发布人:http://www.kdjlm.com    发布时间:2020-06-10 14:14:22

电动卷帘门应有两个限位开关。 一个是上限,另一个是下限。 限位开关应具有机械转动杠杆,以控制开关的停止和启动。
The electric roller shutter shall have two limit switches. One is the upper limit, the other is the lower limit. The limit switch shall have a mechanical turning lever to control the stop and start of the switch.
调整期间,应由两个人操作。 一个人可以调节机械旋转杆在顶部的位置,而另一个人可以控制卷帘门的上下位置来配合调节限位开关的位置。
During the adjustment, it should be operated by two people. One person can adjust the position of the mechanical rotary lever at the top, while the other person can control the up and down positions of the roller shutter door to coordinate with the position of the limit switch.
卷帘门极限调试方法:
Limit debugging method of rolling shutter door:
1.将限位器上的螺母卡旋转到合适的角度以脱开塞子螺母,或松开限位器上的锁紧螺钉。
1. Turn the nut clamp on the stopper to a proper angle to release the plug nut, or loosen the locking screw on the stopper.
2.将门打开到合适的位置后,旋转限位器上的限位螺母使其压住开门限位开关上的滚轮。 听到“嘀嗒”声后,将螺母卡卡入到相应的限位螺母中或是拧紧螺钉。
2. After opening the door to a proper position, turn the limit nut on the limit device to press it against the roller on the limit switch. After hearing the "ticking" sound, clip the nut into the corresponding limit nut or tighten the screw.
3.将门关闭到合适的位置后,转动限位器上的限位螺母使其压住关门限位开关上的滚轮。 听到“嘀嗒”声后,将螺母卡片卡入到相应插槽中的限位螺母中或拧紧螺钉。
3. After closing the door to a proper position, turn the limit nut on the limit device to press it against the roller on the limit switch. After hearing the "tick", clip the nut card into the limit nut in the corresponding slot or tighten the screw.
4.如果门的位置不合适,则可以再次将其调节到最佳位置。
4. If the position of the door is not suitable, it can be adjusted to the best position again.
卷闸门的设置要求规定:
The setting requirements of the rolling gate are as follows:
1.当挂钩滑动到极限位置时,便抬起杠杆。 当按下限位开关时,电路将关闭,再合匣时,挂钩才能下降。
1. When the hook slides to the limit position, lift the lever. When the limit switch is pressed, the circuit will be closed, and then the hook can be lowered when the box is closed.
2.在轨道的端头(在操作限定的位置)安装一个固定的限位挡板。 当塔式起重机运行到该位置时,限位挡板触碰行程开关的扳把,切断电源以控制行程。再合闸时,塔吊只能以相反的方向运行。
2. Install a fixed stop plate at the end of the track (at the position limited by the operation). When the tower crane moves to this position, the limit baffle touches the handle of the travel switch to cut off the power supply to control the travel. When reclosing, the tower crane can only operate in the opposite direction.
3.在盘的中央安装垂直移动的指针。 当改变振幅时,指针指示出在各种振幅下的额定起重量。 当动臂杆移动到上限和下限位置时,分别按下限位开关,切断主控制电路,变幅电机停车,并达到限位的作用。
3. Install the vertically moving pointer in the center of the disk. When the amplitude is changed, the pointer indicates the rated lifting capacity under various amplitudes. When the boom moves to the upper and lower limit positions, press the limit switches respectively, cut off the main control circuit, stop the luffing motor, and achieve the function of limit.
上一篇:济南卷帘门维修需要注意的几个问题?
下一篇:济南车库门几种风格选择
产品中心
联系我们